Page Turn Options

On this page we show you the page turn options for the different view modes.

Image 1 - Display Mode - One Page View

One Page View

Image 2 - One Page View - Full page.

The One Page view displays only page at a time as shown in Image 2.

It is the only view for portrait orientation, so it is used here automatically.

For landscape screens you can also set it using the "Display Mode" settings as shown in Image 1. You simply press the One Page icon 1 to activate it.

The One Page view has three ways of turning pages.

These ways are activated with "Turning Mode" (2) as seen in Image 1:

• Full - this always turns the full page. So you always see the page like in Image 2.
• Half - this allows you to turn pages half as shown in Image 3. The top part 1 shows the next page and the bottom 2 the current page. This allows you to read from bottom to top without turning. When you are reading on top you turn again and it will show top page in full.
• Page Defined - With this setting you can choose between Full and Half for every single page seperately. This is configured by using "Page Settings".

Image 3 - One Page - Half Turn

The settings of the pages can be customized in "Page Settings".

To get there you press "Page Settings" 3 as shown in Image 1.

Then you get the Page Settings screen where you see overview of all pages.

This screen is shown in Image 4.

To change setting follow these steps:

1. First press the edit icon 1 next to the page you want to setup.
2. Then make sure the tab in settings area is on "Single Page" (2).
3. Now you can setup the "Stardard Page Turn" 3. This settings can be "Whole" or "Half".
4. Also you can setup the "Half Page Break" 4 by changing the slider. The result will show in the preview 5. You can also click on that preview to change the page break.

Image 4 - Page Setting - One Page View

Image 5 - Display Mode - Two Pages

Two Page View

Image 6 - Two Pages Display

Two Page View is a view that can be used on landscape screens.

As shown in Image 6 this mode displays two pages next to each other.

You can set it in "Display Mode" settings as shown in Image 5.

You simply press the Two Page icon 1 to activate it.

The Two Page view has four ways of turning pages.

These ways are activated with "Turning Mode" 2 as seen in Image 5:

• 12-34 - This turns pages by two pages at a time, so 12->34->56->....
• 12-32 - Here it turns one page at a time, first it changes the left page, then the right page. So you get 12->32->34->54->....
• 12-23 - This changes both pages to the next one, so it will advance one page. This will result in following order: 12->23->34->56->....
• Page Defined- With this setting you can choose page turn for every single page seperately. This is configured by using "Page Settings".

Image 7 - Page Settings - Two Page View

The settings of the pages can be customized in "Page Settings".

To get there you press "Page Settings" 3 as shown in Image 5.

Then you get the Page Settings screen where you see overview of all pages.

This screen is shown in Image 7.

To change setting follow these steps:

1. First press the edit icon 1 next to the page you want to setup.
2. Then make sure the tab in settings area is on "Two Pages" (2).
3. Now you can setup the "Stardard Page Turn" 3. You can set this to values 12-34, 12-32 and 12-23.

Image 8 - Display Mode - Half Page View

Half Page View

Image 9 - Half Page View

Half Page View can be used on landscape screens.

As shown in Image 9 this mode diplays half of the page.

You can set it in "Display Mode" settings as shown in Image 8.

You simply press the Two Page icon 1 to activate it.

Image 10 - Page Settings - Half Page View

By default the best half page break is automatically detected.

If it's not correct then you can correct it in "Page Settings"

To get there you press "Page Settings" 2 as shown in Image 8.

Then you get the Page Settings screen where you see overview of all pages.

This screen is shown in Image 10.

To change setting follow these steps:

1. First press the edit icon 1 next to the page you want to setup.
2. Then make sure the tab in settings area is on "Half Page" (2).
3. You can setup the "Half Page Break" 4 by changing the slider. The result will show in the preview 5. You can also click on that preview to change the page break.

Sometimes you will see a gray area in half page view line in Image 11.

This shows the area of the other half, so that part you do not need to read.

Only the white part is of the current half.

Image 11 - Half Page View - Gray Area